Barrisol® Track & Profile Range
The Barrisol® Star track is made of aluminium. It is attached on the wall and is invisible after the ceiling is installed
AutoCAD Blocks for the full range of Barrisol® Stretch Ceiling Systems is now available at
Barrisol® Stretch Ceiling installation basics
Barrisol® Stretch Ceiling CAD Block Dimensions
Standard star profiles
The Barrisol® BS350/01 Profile is one of the most common. It is normally wall fixed around the perimeter of the room. For 3D projects the 35001 can be formed into shaped. This profile is made of extruded aluminum.
The Barrisol® BS350/11 Profile is normally ceiling fixed around the perimeter of the room. For 3D projects the 35011 can be formed into shaped. This profile is made of extruded aluminum.
The profile BS350-06 is used for neatly finishing a visible edge on a Barrisol® Stretch Ceiling.
The Barrisol® BS35015 is used when transitioning between two surfaces joining at 90deg (wall to ceiling)
The BS350-01 profile is used for joining Barrisol® stretch ceiling sheets on vertical surfaces.
The BS350-02 is used as a separator / joint when using a number or large sheets or a change in material.
The BS350-18 can be used for joining sheets and for services. Lights, Sprinklers etc can be cut into the 350-18 using standard installation methods.
The Barrisol® MiniStar BMS340-01 is used with the smaller star harpoon system, creating a near invisible joint against a vertical surface.
The Barrisol® BS355/10 is used for wall fixing a double sheet ceiling, normally used for illuminated ceilings.
The Barrisol® BS355/35 profile is used for translucent ceilings with back lighting. This profile holds two ceiling sheets, to top sheet stops debris falling on the lower illuminated stretch ceiling. The difference with the 355-35 compared with 355-14 and 15 is it has a side fixing allowing for easy removal with access to the fixings from below.
The Barrisol® BS355/45 profile is used as a frame for double sheeting. As you can see the material wraps around the outside of the frame and secures in the ledge on top.
The Barrisol® BS355/55 profile is used for frames that can be hung from the ceiling with the material going around the outside and slotting in the ledge just before the top of the frame.
The Barrisol® BS355/14 profile is used for translucent ceilings with back lighting. This profile holds two ceiling sheets, to top sheet stops debris falling on the lower illuminated stretch ceiling.
The Barrisol® BS355/15 profile is similar to the 35514 and again is used for translucent ceilings with back lighting. This profile is slightly larger and used for larger lighting features.
The Barrisol® BS350/61 profile is for curved edges. As you can see the cuts in the frame allow for it to be bent around and object or a corner and the material fitted around.
The Barrisol® BS350/165 profile creates a curve for the material to go around in a neat and profesional way.
The Barrisol® BS350/04 profile leaves a bigger gap between material and the vertical surface. It is normally wall fixed around the perimeter of the room.
The Barrisol® BS350/05 profile leaves a bigger gap between the material and the vertical surface with another ledge at the bottom. Which allows for objects such as picture frames to be hung from it.
The Barrisol® BS350/16 profile helps you bring together two pieces of material with only a small gap in between.
The Barrisol® BS350/19 profile allows for sprinklers and partitions to be put in between each piece of material.
The Barrisol® BS350/20 profile lets you bring two pieces of material right next to each other with no gap showing. Even though this is very tidy the frame has to be put up in two separate parts and then aligned so each piece meets perfectly.
The Barrisol® BS350/21 profile can fit to little partitions or ridges in the ceiling. You can then stretch two pieces of material into the frame each side with only a 6mm separation.
The Barrisol® BS350/22 profile allows for two sheets to be fitted which stops debris getting on the lower sheet. It also allows you to balance a separate part of the ceiling onto the ledge at the side of frame which will hold it up.
The Barrisol® BS350/23 profile separates two pieces of material but attaches flush on to the top of the ceiling.
The Barrisol® BS355/02 profile is for modular frames which can be suspending from ceilings.
The Barrisol® BS355/04 profile is for a modular frame which can fit flush to the ceiling. The material goes into the bottom of the frame but arches in at an angle from the sides.
The Barrisol® BS 355/05 profile slots into another piece of framework which is attached to the ceiling. The framework would come in two half’s and the material would have to be slotted in place before the the profile is fitted into framework actually attached to the ceiling. This therefore allows for a small separation between the two pieces.
The Barrisol® BS355/06 profile can be suspended from the ceiling with the material fitting around the edge underneath the frame.
The Barrisol® BS355/08 profile is a double sheet modular frame which helps keep the bottom sheet clean from debris.
The Barrisol® BS355/17 profile to be used for free hanging frames.
The Barrisol® BS355/18 profile runs along with the BS355/17 which would hang the frame from the ceiling.
The Barrisol® BS355/25 profile can be fixed to the wall and is used for double skins to stop debris getting on to the lower sheet. It also comes of the wall a bit further than the others to leave a wider gap.
The Barrisol® BS355/163 profile is used for dual sheet installation with additional bracing in the walls for larger areas. This profile can be used for both suspended and ceiling fixed light boxes.
The Barrisol® BS365/20 is a tubular frame allowing the Barrisol® fabric to be wrapped around the curved edge creating a smooth profile for Barrisol® structures.
The Barrisol® BS365/30 profile allows multiple sheets to be installed from one point.
The Barrisol® Classic B301 profile is designed to be wall fixed with a 90 degree lower return.
The Barrisol® Classic B311 profile is designed to be wall fixed with a curved lower return.
The Barrisol® Classic B315 profile allows the installation of linear light fittings to be fitted directly to the Barrisol® separator.
The Barrisol® Classic B316 profile allows larger ceiling panels to be joined together to allow the Barrisol® ceiling to cover larger areas.
The Barrisol® Classic B317/01 profile allows the Barrisol® sheet to be formed around columns or corners without the need for a joint.
The Barrisol® B318/01 profile allows multiple sheets to be fitted separating the sheets with a small gap.
The Barrisol® Classic B318/011 profile holds the material in place with the ridges on the frame.
The Barrisol® Classic B320 profile fits off the wall creating a curved frame with the material fitted into the top.
The Barrisol® Classic B326/01 Profile is normally ceiling fixed around the perimeter of the room. For 3D projects this can be formed into shaped. This profile is made of extruded aluminum.
The Barrisol® Trempo BT320 profile consists of fixed springs holding the Barrisol® material to the frame.
The Barrisol® Trempo BT310 profile consists of fixed hooks and rope holding the Barrisol® material to the frame.
The Barrisol® Trempo platte profile consists of reinforced corners which are hooked into place holding the Barrisol® material to the corners.
If you would like and further information on Barrisol Stretch Ceilings, please do not hesitate to contact Barrisol® Welch